Length: 3000mm, Width: 40mm, Thickness: 20mm
Sorry, This Product Is No Longer Available.
This Wood Upstand Has A Gorgeous Cherry Pattern With A Solid Wood Finish. Dimensions: 3000 X 40 X 20mm
Wood worksurfaces are crafted from solid hardwood timber staves and finger jointed in length. The wood is then butt jointed and glued together along its width and finely oiled to create a beautifully water repellent surface. Wood worksurface products have a treasured history in commercial and residential environments, whether contemporary or classic in style. Cherry has a distinctive grain and a lovely rich red tonal wood which will darken over time to give a very natural feel to your kitchen. The distinctive caramel figuring of a cherry worktop will rejuvenate your kitchen as only a fine-quality natural product can. For a splash of colour and warmth, choose cherry. Our timber worksurfaces are manufactured from timber staves 40mm wide ± 2mm (can vary within this across the worksurface but each strip of staves is consistent along the length), the staves are finger jointed end to end into strips that are laminated across the worksurface. All glueing According to EN 204 -D3. The moisture content of each worksurface is 10% ± 2% and specified with an A Face and B face. Its made from staves selected to look 'ï¿½clean'ï¿½ and to not contain dead knots, bark pockets, mineral streaks, rough grain, large colour contrasts, large groups of live knots, Wormholes. General Specifications: Storage: Timber worktops should be stored at room temperature away from all sources of heat and moisture prior to installation. An external room without heating, ie. A garage is not suitable and could cause warping/swelling. Please either store flat or on their longest edge as instructed on the packaging. Never prop up a worktop vertically against a wall. Ideally stored horizontally on a sound and level surface, with timber battens placed between each worksurface at 600mm centres maximum. Stain: It is important to remember not to leave wine glasses, dishes containing curry, wet copper 'ï¿½ bottomed pans or similar items on wood worksurface products. Scratch: Wood worksurface products may be more prone to scratching than some other surfaces. The use of chopping boards and / or pastry mates is recommended in order to protect the surface finish. Thermal Expansion: Wood worksurface products should ideally be kept at room temperature. In kitchens where temperatures can be either very cold (unoccupied site) or very humid, then the level of maintenance required is greater, especially in the immediate days / weeks after installation. In these cases extra coats of worksurface sealant will be necessary to prevent drying out and warping. If an under oven, dishwasher, washingmachine or tumble dryer is to be installedunder the worksurface, a piece of aluminium foil should be adhered to the underside, with the foil face outwards. This will protect it from any intense heat or moisture. Allow a 3-4mm gap between the back edge of the worktop and the wall to allow expansion and contraction. Repairable: Although the first few marks and scratches will stand out dramatically, hardwood has many unique qualities and with a little care and attention the passage of time can enhance its beauty. In the unfortunate event of sustaining damage, a wood worksurface maybe rubbed down and refinished, leaving it as good as new. Cleaning: All spills should be cleaned up immediately. For daily cleaning we recommend a solution of warm water with a drop of washing-up liquid. Soak a cloth in the solution, wring out until almost dry and wipe the down the worksurface. Fitting Options: Joints: Wood worksurfaces can be butt or mitre jointed dependent upon the edge detail. Mitre joints require additional support on site and require an additional length of worksurface to install. Overhangs & Support: Any overhang extending more than 300mm must be supported. Points of Note: Plastering or tiling should be completed after installation. When fixing to the cabinets, only use slotted angle brackets to secure the worktop to the carcass. Always use washers with screws. If a carcass has a solid top, or you can only secure through the top rail always drill an oversized hole (8 'ï¿½ 10mm) through the top of carcass and secure to the worksurface using a larger washer and screw. This allows the worksurface to slide over the washer in case of natural expansion or shrinkage.
Constructed from 40mm wide staves
Quality Grade 'A' FSC Timber
Finished to a silky smooth 220 grit
Tolerance in wood is Â±2mm
Moisture content 10% Â±2%
Sealant is brushed on leaving a clear, water repellent finish
The staves are finger jointed end to end into strips
All glueing according to EN 204 -D3
Individually shrink wrapped to protect against moisture and warping
Bring natural beauty in your kitchen
|Brand:||Hc Supplies Wood|
If you want to return your product bought from HCSupplies you have until the seventh day after delivery of the item to let us know in writing that you would like to return your item for a refund. Please send us an email to [email protected] or write to us at our address on our contact page. This however does not apply to any item(s) from our kitchen worktops range. For example, kitchen worktops, breakfast-bars, splashbacks and upstands cannot be returned.
In the unlikely event your product arrives damaged or is faulty please contact us to arrange a replacement or refund. Worktops need to be checked on delivery and refused if any damage is present. For all other items please open and check your items as soon as possible and notify us within 24 hours of delivery if there are any damages.
Please note that although that every effort has been made to ensure that the image on this page represents the product as best it can, all screens display colours differently due to a variety of reasons such as the type of screen and the settings. Therefore, we always recommend that you request a free worktop sample. Laminate samples can be requested by clicking here. If you require a sample of a worktop that is not a laminate worktop then please contact the manufacturer directly. Please allow 5-10 working days for sample requests due to the large volume of requests that we receive.
All products should be checked for any damage on delivery and solid surface products should be checked for colour consistency prior to installation. Any claims after installation relating to colour inconsistency are not covered by the product warranty.
Please note that items from the following brands/ranges are made to order and therefore once an order is placed a cancellation is not possible: Apollo Magna, Apollo Quartz, Apollo Slabtech, Corian, Granite Worktops, Silestone, Zodiaq and Wood Worktops.