Save £££`s On All Worktops & Breakfast Bars at HC Supplies.
£105.60 Inc VAT.
RRP: £176.00 | Fast UK Delivery
£40.00 Standard Delivery
No Matter How Many Products You Order
You Will Only Pay 1 Delivery Charge.
Click On The Sizes Above To Expand Selection.
This Apollo Slab Tech Solid Surface Acrylic End Panel Has A Striking Sea Black Pattern With A Solid Surface Finish. Dimensions:
Mitred Butt Joint is a joint made by beveling each of two parts to be joined, usually at a 45Â° angle, to form a corner 90Â° angle. There have also Standard Butt Joint and Flush Butt Joint available. In all instances the panel will be manufactured to the correct height as this material is not easily scribed to the floor. ApolloÂ® Slab Tech Sea black is manufactured from mineral filled polyacrylate/polyester resins. With superior innovative designs, enduring applications and excellent long-term performance, ideal in both residential and commercial environments. ApolloÂ® Slab Tech has proved itself to be a remarkably durable material; it cannot delaminate and stands up well to daily wear and tear. Apollo Slab Tech is NSF certified and tested to FIRA Industry standards. General Specifications: Cleaning: All spills should be cleaned up immediately, as it is always easier to wipe up a spill than to have to deal with a dried-on stain. For daily cleaning we recommend a solution of warm water with a drop of washing-up liquid. Soak a cloth in the solution, wring out until almost dry and wipe the down the worksurface. If your worksurface has an integrated sink, clean this in the same way as the worksurface. Heat: Do not pour boiling hot water directly into solid surface sinks, and where constant boiling hot water taps are fitted, please ensure they are not left running directly into solid surface sinks. Hot pans should never be placed directly on any worktop and always be placed on pan rests, platters or something similar. Ensure that pans used on gas hobs are of correct size. Heat producing appliances that sit beneath the worktop, must have an aluminium foil membrane placed on underside of worktop. Staining: While most tough stains can be buffed away, a level of care and maintenance is required, as spills should be cleaned up immediately. Accidental spills of strong chemicals, (e.g. paint stripper, brush cleaners, metal cleaners, oven cleaners, cleaners containing methylene chloride, acid drain cleaners, acetone based nail varnish removers etc.), should be washed away immediately using plenty of soapy water to avoid damaging the worksurface. Scratches: ApolloÂ® Slab Tech is scratch resistant but not scratch proof; the use of chopping boards and/or pastrymates is recommended. Dark, heavily pigmented colours will show scratches, dust and ordinary wear and tear more readily than lighter, textured forms. Care should be taken not to slide rough based items over the surface. Thermal Expansion: Due to thermal expansion ApolloÂ® Slab Tech can expand up to 1mm per metre. A gap of at least 3mm should be left at each end of the worktop and filled with decorators caulk. When ApolloÂ® Slab Tech is joined to other materials (such as glass, steel or wood) an elastic type of adhesive, for example polyurethane, is required to let parts expand and contract freely. Repairable: ApolloÂ® Slab Tech can be easily be repaired. Using an ordinary abrasive cleaner and a scouring pad the surface may be fully restored to its original appearance. Hygienic: ApolloÂ® Slab Tech is a non porous material and is naturally resistant to mould, bacteria and mildew.
Manufactured from mineral filled polyacrylate/polyester resins Excellent Stain, scratch and impact resistant Easy to clean and maintain work surface Warm and inviting to the touch Inconspicuous, unobtrusive and seamless joints Tolerance in ApolloÂ® Slab Tech is Â±2mm Accidental damage is repairable NSF certified Tested to FIRA Industry Standards 10 Year Manufacturerâ€™s Limited Warranty
|Material:||Solid Surface Acrylic|
|Brand:||Apollo Slab Tech|
Hob & Sink cutouts: Granite sink / hob cut outs are barred front & back (fitting of steel support bars to give additional support to cutouts), Without steel supports bars, the length of a cut out is reduced considerably. Large cut outs need to be scored and cored on occasions. This leaves the corners of the cutout in place, ready for removal on-site by the installer. Granite is susceptible to ‘blowing out’. This occurs when contact is made with the material whilst cutting or grinding. This is very common in large particled granite. ie. we fill and seal the affected areas with epoxy resin (colour may vary) to ensure the material is not left with any sharp edges or ‘chips’.
A minimum of 120mm is required between two hob cutout, 100mm is required between hob and sink cutouts, 70mm is required between two sink cutouts and sink cutouts are placed 50mm from the worktop front edge.
Stainless Steel Sinks: Please specify the preferred undermounting of Stainless Steel Sinks. Silicone sealant may be rendered ineffective when plumbing the sink in, it is important that the sink is re-sealed by the plumber, or the 12 months guarantee will be invalid if the work is not carried out. If a waste disposal unit is fitted to an undermounted sink after installation, additional support will be required, otherwise your warranty may be invalidated.
Joints: Granite joints are finished with a small ariss to the top edge. Silicone sealant is applied to prevent water ingression.
Overhangs & Supports: Any overhang extending more than 300mm must be supported.Handling: For installations you will need additional labour on worktops weighing above 150kg. Every additional 75kg requires an extra person to assist with lifting. Due to the weight of granite, please ensure that your units are level and securely fixed.Drainer Grooves: Drainer grooves and recessed drainers may be duller than the rest of the polished surface. Colour matching is not always possible as granite can vary dramatically throughout each scant.Points of Note: Hob flanges need to sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat & causing cracks in the worktop.Regular use of your Care & Maintenance Kit should ensure that your worktop always looks good.
If you want to return your product bought from HCSupplies you have until the seventh day after delivery of the item to let us know in writing that you would like to return your item for a refund. Please send us an email to [email protected] or write to us at our address on our contact page. This however does not apply to any item(s) from our kitchen worktops range. For example, kitchen worktops, breakfast-bars, splashbacks and upstands cannot be returned.
In the unlikely event your product arrives damaged or is faulty please contact us to arrange a replacement or refund. Worktops need to be checked on delivery and refused if any damage is present. For all other items please open and check your items as soon as possible and notify us within 24 hours of delivery if there are any damages.
Please note that although that every effort has been made to ensure that the image on this page represents the product as best it can, all screens display colours differently due to a variety of reasons such as the type of screen and the settings. Therefore, we always recommend that you request a free worktop sample. Laminate samples can be requested by clicking here. If you require a sample of a worktop that is not a laminate worktop then please contact the manufacturer directly. Please allow 5-10 working days for sample requests due to the large volume of requests that we receive.
All products should be checked for any damage on delivery and solid surface products should be checked for colour consistency prior to installation. Any claims after installation relating to colour inconsistency are not covered by the product warranty.
Please note that items from the following brands/ranges are made to order and therefore once an order is placed a cancellation is not possible: Apollo Magna, Apollo Quartz, Apollo Slabtech, Corian, Granite Worktops, Silestone, Zodiaq and Wood Worktops.