Save £££`s on all worktops & breakfast bars at hcsupplies until the end of october 2016.

Sale Ends In:

Quick Code: QF6645

Hcsupplies Maple Solid Wood 3000x640x40mm Worktop

Length: 3000mm, Width: 640mm, Thickness: 40mm

£259.16 Inc VAT.

SAVE £259.17 50% SAVING

RRP: £518.33 | Fast UK Delivery

5-15 Working Days
£40.00 Standard Delivery
70% Sale Now On
accepted cards image

Available Sizes:

640mm Worktops

900mm Worktops


Related Accessories:


After Care

Click On The Sizes Above To Expand Selection.

Featured Products

Featured Products

Recently Viewed

Best Sellers In Solid Wood Worktops

No.1 Best Selling Product In This Category: Solid Wood Tiger Walnut 40mm Stave Worktops
Solid Wood Tiger Walnut 40mm Stave Worktops
No.2 Best Selling Product In This Category: Solid Wood Rustic Oak 40mm Stave Worktops
Solid Wood Rustic Oak 40mm Stave Worktops
No.3 Best Selling Product In This Category: Solid Wood Rustic Oak 40mm Stave Worktops
Solid Wood Rustic Oak 40mm Stave Worktops
Full Product Description

This Wood Worktop Has A Beautiful Maple Pattern With A Solid-Wood Finish. Dimensions: 3000 X 640 X 40mm

Wood worksurfaces are crafted from solid hardwood timber staves and finger jointed in length. The wood is then butt jointed and glued together along its width and finely oiled to create a beautifully water repellent surface. Wood worksurface products have a treasured history in commercial and residential environments, whether contemporary or classic in style. Maple worktops embody warmth and versatility; their soft, unique glow is wonderful to behold. Equally at home in a traditional or modern design, these honey-coloured timbers have been a favourite worktop material for many centuries due to their superior density and elegant appearance. Our timber worksurfaces are manufactured from timber staves 40mm wide ± 2mm (can vary within this across the worksurface but each strip of staves is consistent along the length), the staves are finger jointed end to end into strips that are laminated across the worksurface. All glueing According to EN 204 -D3. The moisture content of each worksurface is 10% ± 2% and specified with an A Face and B face. Its made from staves selected to look “clean” and to not contain dead knots, bark pockets, mineral streaks, rough grain, large colour contrasts, large groups of live knots, Wormholes. General Specifications: Storage: Timber worktops should be stored at room temperature away from all sources of heat and moisture prior to installation. An external room without heating, ie. A garage is not suitable and could cause warping/swelling. Please either store flat or on their longest edge as instructed on the packaging. Never prop up a worktop vertically against a wall. Ideally stored horizontally on a sound and level surface, with timber battens placed between each worksurface at 600mm centres maximum. Stain: It is important to remember not to leave wine glasses, dishes containing curry, wet copper – bottomed pans or similar items on wood worksurface products. Scratch: Wood worksurface products may be more prone to scratching than some other surfaces. The use of chopping boards and / or pastry mates is recommended in order to protect the surface finish. Thermal Expansion: Wood worksurface products should ideally be kept at room temperature. In kitchens where temperatures can be either very cold (unoccupied site) or very humid, then the level of maintenance required is greater, especially in the immediate days / weeks after installation. In these cases extra coats of worksurface sealant will be necessary to prevent drying out and warping. If an under oven, dishwasher, washingmachine or tumble dryer is to be installedunder the worksurface, a piece of aluminium foil should be adhered to the underside, with the foil face outwards. This will protect it from any intense heat or moisture. Allow a 3-4mm gap between the back edge of the worktop and the wall to allow expansion and contraction. Repairable: Although the first few marks and scratches will stand out dramatically, hardwood has many unique qualities and with a little care and attention the passage of time can enhance its beauty. In the unfortunate event of sustaining damage, a wood worksurface maybe rubbed down and refinished, leaving it as good as new. Cleaning: All spills should be cleaned up immediately. For daily cleaning we recommend a solution of warm water with a drop of washing-up liquid. Soak a cloth in the solution, wring out until almost dry and wipe the down the worksurface. Fitting Options: Hob & Sink Cut-outs: Sink cut-outs should be a minimum of 50mm from the worktop front edge. Aluminium foil should be applied to the edges of hob cut-outs. There should be a minimum 200mm between hob cut-outs. Hob cut-outs should be a minimum of 50mm from the worktop front edge. Hob flange needs to sit on the aluminium foil around the cut-out, to avoid conducting too much heat into the wood and causing cracking. When a worktop is to be fitted near to an Aga, Rayburn or similar allow a minimum gap of 4mm. Ideally a solid wood return should be fixed across the end grain to stop any splits occurring. Stainless Steel Sinks: Please specify preferred method of undermounting Stainless Steel sinks. There should be a minimum 200mm between sink cut-outs. Drainer grooves can only be cut in the middle of staves, due to the nature of the construction of your worksurface. If a waste disposal unit is fitted to an undermounted sink after installation, additional support will be required, otherwise your warranty may be invalidated. Joints: Wood worksurfaces can be butt or mitre jointed dependent upon the edge detail. Mitre joints require additional support on site and require an additional length of worksurface to install. Overhangs & Support: Any overhang extending more than 300mm must be supported. Points of Note: Plastering or tiling should be completed after installation. When fixing to the cabinets, only use slotted angle brackets to secure the worktop to the carcass. Always use washers with screws. If a carcass has a solid top, or you can only secure through the top rail always drill an oversized hole (8 – 10mm) through the top of carcass and secure to the worksurface using a larger washer and screw. This allows the worksurface to slide over the washer in case of natural expansion or shrinkage.


Square edge Constructed from 40mm wide staves Quality Grade 'A' FSC Timber Finished to a silky smooth 220 grit Tolerance in wood is ±2mm Moisture content 10% ±2% Sealant is brushed on leaving a clear, water repellent finish The staves are finger jointed end to end into strips All glueing according to EN 204 -D3 Individually shrink wrapped to protect against moisture and warping Bring natural beauty in your kitchen

Specification Table:
MPN: - (6645)
Length: 3000mm
Width: 640mm
Thickness: 40mm
Material: Wood
Finish: Solid Wood
Pattern: Maple
Brand: Hc Supplies
Installation Guide

Hob & Sink cutouts: Granite sink / hob cut outs are barred front & back (fitting of steel support bars to give additional support to cutouts), Without steel supports bars, the length of a cut out is reduced considerably. Large cut outs need to be scored and cored on occasions. This leaves the corners of the cutout in place, ready for removal on-site by the installer. Granite is susceptible to ‘blowing out’. This occurs when contact is made with the material whilst cutting or grinding. This is very common in large particled granite. ie. we fill and seal the affected areas with epoxy resin (colour may vary) to ensure the material is not left with any sharp edges or ‘chips’.

A minimum of 120mm is required between two hob cutout, 100mm is required between hob and sink cutouts, 70mm is required between two sink cutouts and sink cutouts are placed 50mm from the worktop front edge.

Stainless Steel Sinks: Please specify the preferred undermounting of Stainless Steel Sinks. Silicone sealant may be rendered ineffective when plumbing the sink in, it is important that the sink is re-sealed by the plumber, or the 12 months guarantee will be invalid if the work is not carried out. If a waste disposal unit is fitted to an undermounted sink after installation, additional support will be required, otherwise your warranty may be invalidated.

Joints: Granite joints are finished with a small ariss to the top edge. Silicone sealant is applied to prevent water ingression.

Overhangs & Supports: Any overhang extending more than 300mm must be supported.

Handling: For installations you will need additional labour on worktops weighing above 150kg. Every additional 75kg requires an extra person to assist with lifting. Due to the weight of granite, please ensure that your units are level and securely fixed.

Drainer Grooves: Drainer grooves and recessed drainers may be duller than the rest of the polished surface. Colour matching is not always possible as granite can vary dramatically throughout each scant.

Points of Note: Hob flanges need to sit on aluminium thermal insulation tape around the cut-out to avoid conducting excess heat & causing cracks in the worktop.

Regular use of your Care & Maintenance Kit should ensure that your worktop always looks good.

Returns & Refunds

If you want to return your product bought from HCSupplies you have until the seventh day after delivery of the item to let us know in writing that you would like to return your item for a refund. Please send us an email to [email protected] or write to us at our address on our contact page. This however does not apply to any item(s) from our kitchen worktops range. For example, kitchen worktops, breakfast-bars, splashbacks and upstands cannot be returned.

Faulty or Damaged Items

In the unlikely event your product arrives damaged or is faulty please contact us to arrange a replacement or refund. Worktops need to be checked on delivery and refused if any damage is present. For all other items please open and check your items as soon as possible and notify us within 24 hours of delivery if there are any damages.

Important Information

Please note that although that every effort has been made to ensure that the image on this page represents the product as best it can, all screens display colours differently due to a variety of reasons such as the type of screen and the settings. Therefore, we always recommend that you request a free worktop sample. Laminate samples can be requested by clicking here. If you require a sample of a worktop that is not a laminate worktop then please contact the manufacturer directly. Please allow 5-10 working days for sample requests due to the large volume of requests that we receive.

All products should be checked for any damage on delivery and solid surface products should be checked for colour consistency prior to installation. Any claims after installation relating to colour inconsistency are not covered by the product warranty.


Please note that items from the following brands/ranges are made to order and therefore once an order is placed a cancellation is not possible: Apollo Magna, Apollo Quartz, Apollo Slabtech, Corian, Granite Worktops, Silestone, Zodiaq and Wood Worktops.